Ventilator

Ventilator

Item Code: OTE-07

Power Line 220 VAC range (220-240 VAC), 0.5 Ampere, 50/60 Hz., external voltage selector switch. Gauge: Use 3-conductor harmonized cord only; up to 49′ use 18 gauge cord; up to 99′, use 16 gauge cord; up to 200′, use 14 gauge cord. External Battery: 12 VDC, 5 Amperes. Approximately 20 hrs. operation with 75-80 Amp-hour 12 VDC deep-cycle, gel-cell battery. Approximately 10 hrs operation with 35-40 Amp-hour 12 VDC deep-cycle, gel-cell battery. Internal Battery: Approximately 1 hour operation. Type: Volume ventilator. Motor Brushless induction. Pump: Piston, 100 to 2200 ml tidal volume capability. Front Panel Controls: Alarm Silence/Reset: Push button to silence alarms during events or reset after events; used with Battery Test button to read machine operating hours on Patient Pressure meter Battery Test: Push button to show battery charge level on the lower window of Patient Pressure meter. Mode: Rotary switches to set ventilator operating mode: Standby, Assist/Control, SIMV, or Pressure Cycle. Low Alarm: Rotary switch to set limit for Low Pressure alarm: 2 to 32 cmH2O/hPa in increments of 2 cmH2O/hPa High Alarm Limit: Rotary switch to set limit for High Pressure alarm {Assist/Control, SIMV modes} or limit for Pressure Cycle mode: 15 to 90 cmH2O/hPa in increments of 5 cmH2O/hPa Volume: Push-to-turn knob to set volume: continuously adjustable from 100 to 2200 ml. Breath Rate: Rotary switch to set breathing rate: 120 BPM in increments of 1 BPM and 2238 BPM in increments of 2 BPM. Inspiratory Time: Rotary switch to set time for delivery of set volume: 0.5 to 1.0 sec. in increments of 0.1 sec.; 1.2 sec.; and 1.5 to 5.5 sec. in increments of 0.5 sec. Breathing Effort: Push-to-turn knob to set pressure level for detecting breathing effort; continuously adjustable from -10 to +10 cmH2O/hPa Pressure Limit (LP10 Only): Locking knob sets pressure limit level from 15 to 50 cmH2O/hPa or closes off the pressure limit feature. Input Patient Pressure: Port for connection to the proximal pressure line of the patient circuit. Outputs Patient Air: 22 mm tube for connection to the bacteria filter. Exhalation Valve: Port for connection to the exhalation valve of the patient circuit. Indicators Normal Events Patient Pressure Meter: Displays patient pressure, -10 to +100 cmH2O/hPa; also displays battery charge and machine hours of operation when appropriate buttons are pressed. Breathing Effort: Green LED activated by adequate patient breathing effort. Power: LEDs indicate operating power source: green AC Pwr/Batt Charge, amber External Battery, flashing amber Internal Battery. Alarms: Flashing red LEDs: Low pressure /Apnea, Low Power, High Pressure, Setting Error, Power Switchover. Audible Alarms Pulsating Tone: Low Pressure/Apnea, Low Power, High Pressure, Setting Error, Power Switchover. Steady Tone: Loss of microprocessor control. Reminder Tone: Every five minutes when powered by Internal battery, each time accessory printer generates a report. Rear Panel Controls AC Circuit Breaker Internal to the AC Power Switch (1 for ON; 0 for OFF), 1 Ampere Inputs Inlet Filter: Intake for patient air. Screw off cap for filter change. External Battery: Connection for 12 VDC battery. Communications Port Calibration information during service procedure. Outputs Vent: Cooling vent for internal ventilator components Remote Alarm Connection for optional alarm accessories. Communications Port Connector for optional printer